- What tool did you use?
- Europeans dont tune.....much, does anyone sell reasonably priced head/cam combos?
- best cam for 50trim with nitrous???
- The point in 5 layer head gaskets?
- BC S3 pretty identical to Crower S2's?
- Gauging Interest: Boomba Cam Gears
- How do you adjust your cam gear?
- 18's & bc springs
- cam caps
- head build ?????
- Quick 2.0 cam question.
- Fouled plugs
- Crane 12 cam tune?
- 2.0l cam video's
- specs for tightening down stock headstuds?
- 2.0 cams?
- My head build
- oil problem
- compress test,good....why smoking
- Need Help
- Crower Stage 2's on stock head/springs?
- crower stage 1 cams stock head?
- Where to get crane 16 cams and accesories
- Fidenza cam gears?
- CAM AND VACCUM Question
- this is why u dont have ur local machine shop port ur head.........
- CROWER stage 2 cams=?
- Cam setup?
- New Mopar Head Question - Assembled?
- cylinder 1 low compression 130psi
- Excited for head!
- head bolt torqe spec
- Need Quick Response.. Camshaft Position Sensor
- Help With ENGINE PROBLEM...
- Dyno with 2.0 cams
- Need valves.... which ones do i use?
- Knocking noise from top of motor!!! Please help!!!
- BC3's make no difference?
- Time to break in a head?
- Reusing my lifters, need help for install..
- crane 14 exhaust cam
- HELP compression check ?
- ARP ever fix their headstuds?
- timing belt jumping?
- where to buy crane 18's
- 1 vs. 3 groove valves
- is it possible?
- Porting ur own head
- 2.0 cams... need help.
- how much does compression affect detonation?
- Best price for Crane Cams...
- think my headgasket is blown
- JE 8.5:1's + Crower s2's = AHH! ?
- Solid lifters?
- dcr headgasket blowing antifreeze cloud after 6 months
- any suggestions??
- Put head on or wait?
- how many people are running stock spring and retainers on cams?
- 2.0 cam install...
- head removal
- How to lower comp ratio?
- Crank pulley stuck on
- 2.0L DOHC valves?
- Ported turbo and exhaust manifold on built head
- Crane 14 Starting point
- Cam help.
- ?????bc Stage 2 Cams With Stock Turbo?????????
- +1mm vs. +2mm valves
- custom regrinds?
- installed cams..now 2 plugs broke..
- stock cams, hp61, EMS shifting at 6800 or so, BIg turbo owner input needed!!!
- Cylinder Head work?
- Po340 and no it's not the same question
- Best Cam Shafts for Built 35R Setup??
- Screw size on the Fidanza cam gears?
- people w/ BC3's. how's your idle?
- Valve question
- specs on Crower S3 272's NOT Brian Crower
- 2.0 cam guys... where are YOUR gears set at?
- I Need Info Please For Bc Camshafts Stage3
- crane 16's
- Some really nice port work
- Crower 272's
- Safe Boost w/stock headgasket
- i just ordered my 2.0's ;)
- Which has the higher lift?
- Cams
- DIY head: cut the guides?
- Bc Stg2 Dyno Info?
- question on bc cams???
- What cams with stage 3 with dcr ported head?
- loud ticking in the engine bay. ideas/need help!?
- 2.0L's gone wrong
- How to store a head
- white smoke
- BC cams Vs Cali Smog????
- a simple question regarding stock cams
- thinking about putting stock ones back in
- Bc Or C
- difference in +1mm and +2mm exhaust valves?
- Lotus R/T Head vs. 2.4 DOHC Head
- which cams fidanza or Unothodox
- The best cam gears ever!!! Take a look!!
- 50trim & 2.0cams = no good?
- Fidanza Cam Gears old or new?
- 1st Gen Neon Cam Question
- cam question
- Increased RPM
- need help cam noise??????
- 2.0L cam tuning
- competiton street cam?
- new valves - where to buy
- settings for crane 14 with fidanza cam gears ?
- OK Head and Cam Gurus.......
- best cams
- Need to know numbers on cams??
- BC Stg3 questions..
- Turbo PT Head?
- Crane 16s - Stage 2 Stock Turbo?
- Best place to get BC springs and valves
- Who's ported head to go with?
- fidanza cam gears and bc stage 3's
- Which head is the SRT-4
- cant get the crank pulley off
- bc 2 cams
- Oversized Valves? Where/Who to buy?
- lost cam cap sequence
- need the size of fidanza hardware.
- best cam for this particular set? stuck.
- stock headbolts good to what hp?
- 2.0's review
- help. threw off my whole timing.
- What's a good Head Gasket
- torque specs for arp headstuds
- I need LSA specs for...
- 2mm or 3mm ex valves
- had a crack block change to new block
- How do you widen LSA
- how important is valve train w/ ...
- new Port & Polish... it's awsome!!!
- will the new.....
- Cam slot on head is worn
- BC S3 or Crane 16? I need your choices and your opinions
- Specs on original Crower 2's
- Not sure where to post this question
- weird clicking noise under valve cover??
- Crane 14 Cams - Blow out pricing!!!
- Cam Question
- Any one Running Brian Crower Stage 3's?
- Cams for a 20G setup?
- brian crower stage 3 cams?
- removing cam sprockets w/o removing the VC?
- benfits of 2.o cams
- Need info on tuning bc stage 2 cams please!
- Oil on top of head, need some help.
- 1st Rough Cut on the Cylinder Head
- need the part # for the chrysler 3jaw pulley remover
- What would you do????
- which cam for stock turbo
- stock valve springs w/ crane 14's
- dcr timing belt tensioner?
- What cams for a s20g/50trim hybrid turbo???
- Cam seals ? Part# ?
- are these cam gears (old fidanzs) junk? *pics*
- which way should i degree my cam gears??
- Best cams for a 44lb S3
- broke bolt off under valve cover
- timing belt walkthrough?
- skipped tooth on crank pully. is it possible?
- cam question.
- weird question
- Need some suggestions.....Head Guru's....
- Need some info on cams/cam gears :D
- anybody ever have this happen? plz look
- what stage cams?
- stock cam gears on bc 3's
- Should I be concerned about the ticking noise coming from valve cover?
- PART 2!!!!!! LOOK AT THESE PICTURES!!! (timing belt)
- guys look at this picture and tell me if this is ok
- Help Asap!! Please Read Nowww!!!
- head studs?
- oversized valves- what about seats?
- tick tick tick
- Got a deal on crane 16's
- Top end noise?
- help with.........lifters?????/
- crower stage 2 cam spec sheet
- what cam r good to get
- 2.0 cams
- BC stage 2 cams
- Adjusted my BC stage 3 cams...
- Cutting Motor Mount
- I need Intake valves for my DCR Race head
- Pics of my Performance CnC Race(CnCport.com) Head!
- pulling the head...i have questions.
- new/old fidanza??? help please!
- what cams/cam gears route should i go with?
- Help - Head Cover Double Stud Locations
- head porting???
- P0340-camshaft Position Sensor Circuit
- Crane or Crower cams?
- What Cams For 50 Trim?
- I'm upgrading my head and need some advice
- Cam Tuning
- DCR Head Gasket?
- cam magnet
- which valves to get
- who is running crower Stg 3's?
- Possible to fix Fidanza cam gears?
- What's your Crane 14's timing settings?
- rev valves require 1st gen locks??? wtf??
- HELP: BC Stage 3 Cams / Vacuum
- tapping / ratteling by under oil cap??
- Need a head
- quick head stud question
- Help -> DTEC, .50 Trim, 750s+RL, Crane 14's baseline info
- PT 2.4L and SRT4 head difference
- what cam for Stage 3 car?
- Best to wait?
- are you retarded
- Crane 14's - HELP!
- Crane 18's
- ? before i install my 2.0's...urgent!
- need help!!!!!!!! cam gear install, need help asap!!!!!!!!!!!!!!!!
- HELP! Not sure if anyone in here can but im going to try!
- Where to buy BC s3 cams?
- help me decide ... 60 trim .. what cams??
- 2.0 cams ? or 14s
- great info on head porting
- Heads, heads and more heads...
- ARP head studs
- Crane 12's or 2.0 cams??
- 2.4 non srt head??
- Eaton Lifters???
- Why arnt crane 14's used much?
- PnP Head Owners Answers Only Pls
- explain why no timing cover w/ fidanzas
- For those of you with Brian Crower stage 3's and BC springs and retainers.
- Port and Polish
- I know this has been asked...sorta
- Crane 14's Timing.
- crower stage 3's vs crane ?
- please help asap
- factor tq specs
- What Cam - AMS Motor/Head build - DBB 50
- fel-pro head gasket? anybody ever heard of them
- car made less power need help!
- when do the 16's run out of steam??
- 16s over 12s Y OR N - TO THE CAM GURUUUUUUUUU'S
- Cam ?s